Connection Ethernet due and power bar board

[majid.gh]

Hello 

please see




Works Button Feed Fish and power control  

But information not shown  

######################################################################################
test

Initializing sd card...
SUCCESS - sd card initialized.
Wait 5 seconds for test to begin
Serial1 Sent Signal to Power Bar
Serial1 Received Signal From Power Bar
Serial1 Working
Serial2 Sent Signal to Power Bar
Serial2 Received Signal From Power Bar
Serial2 Working
Checking Expansion Hub

[Tupac]

Does the information show on the controller screen?

[majid.gh]

Thanks for answer

Yes fully show on the screen

[Tupac]

Thanks for answer

Yes fully show on the screen

Might be the IC on the power bar board (the one with the Mega) right above the header connecting the 2 boards.  I had a similar problem except the sensors would read on the web but not on my screen.

Check that you get a 5v reading from all the pins marked in red in the pic.

[majid.gh]

Thanks for answer

Yes fully show on the screen

Might be the IC on the power bar board (the one with the Mega) right above the header connecting the 2 boards.  I had a similar problem except the sensors would read on the web but not on my screen.

Check that you get a 5v reading from all the pins marked in red in the pic.

Thanks Tupac

All the red pins is 5v


I have problem Connection the Ethernet board with Mega board

No Mega board with display board  ...
...........................................................................
But Works Button Feed Fish and power control in the web  

..........................................................................
Not shown any information in the network settings

please see pic

[Rob F]

Hi Majid, if you can feed the fish from the internet its working ok. There's a small bug so do the following.

From the home page press "settings", "customize", "outlets" and then exit the screen.

As soon as you exit the screen all the outlets should fill in, you can keep the webpage open when you do it.

I think there could be an issue with the network info but that doesn't affect anything. I think its having trouble retrieving your external IP, I'll be looking into it soon.

[majid.gh]

Hi Majid, if you can feed the fish from the internet its working ok. There's a small bug so do the following.

From the home page press "settings", "customize", "outlets" and then exit the screen.

As soon as you exit the screen all the outlets should fill in, you can keep the webpage open when you do it.

I think there could be an issue with the network info but that doesn't affect anything. I think its having trouble retrieving your external IP, I'll be looking into it soon.

Hi Rob


I have done such as you in the video (From the home page  "settings", "customize", "outlets" and then exit the screen)
But the problem persists

Rob , Why sensor data(web page) does not show anything ?

Note: I do not put my ID on Twitter

[Rob F]

I just checked that test sketch that you ran, there is a problem communicating from the ethernet board to the power bar board. I'm not sure how you setup the logic level converters but you need to check the connections between the ethernet due and mega.

The test sketch should output this when its working.

Initializing sd card...
SUCCESS - sd card initialized.
Wait 5 seconds for test to begin
Serial1 Sent Signal to Power Bar
Serial1 Received Signal From Power Bar
Serial1 Working
Serial2 Sent Signal to Power Bar
Serial2 Received Signal From Power Bar
Serial2 Working
Checking Expansion Hub
________________________ you need the two lines below to show up next.
Ethernet Hub Successful
Test Complete

It doesn't matter about twitter ID, that's only for web alerts.

[majid.gh]

I just checked that test sketch that you ran, there is a problem communicating from the ethernet board to the power bar board. I'm not sure how you setup the logic level converters but you need to check the connections between the ethernet due and mega.

The test sketch should output this when its working.

Initializing sd card...
SUCCESS - sd card initialized.
Wait 5 seconds for test to begin
Serial1 Sent Signal to Power Bar
Serial1 Received Signal From Power Bar
Serial1 Working
Serial2 Sent Signal to Power Bar
Serial2 Received Signal From Power Bar
Serial2 Working
Checking Expansion Hub
________________________ you need the two lines below to show up next.
Ethernet Hub Successful
Test Complete

It doesn't matter about twitter ID, that's only for web alerts.

Not show
                 Ethernet Hub Successful
                 Test Complete

[Rob F]

There's definitely a problem then. Not sure how you have it setup but its there somewhere, you come this far, almost there, you'll get it.

[majid.gh]

There's definitely a problem then. Not sure how you have it setup but its there somewhere, you come this far, almost there, you'll get it.

The problem was solved


Thanks Rob

[Rob F]

Nice, I knew you could do it. 

I'm curious do you have all the network info showing on the system settings page now?

[rott]

and is your Ph really 4.36 that is almost acid

[majid.gh]

and is your Ph really 4.36 that is almost acid

Add ph minus sera for testing ph meter

[rott]

glad to hear it was for testing only