Posts: 25
Threads: 5
Likes Received:
0 in 0 posts
Likes Received:
0 in 0 posts
Reputation:
0
Joined: Jan 2016
Country:
Hi Rob
The connection between power bar and the display is red. In the beginning is green, after a few seconds is red. Blinking green, red, green ,red...
I did restore the controller to defaults as per instruction but still is red.
I replaced with a new cable but the problem is the same.
Thanks in advance
Posts: 3,251
Threads: 90
Likes Received:
163 in 120 posts
Likes Received:
163 in 120 posts
Reputation:
184
Joined: Sep 2015
Country:
Hi Vilich, I assume it was working ok before the update? Try reprogramming the arduinos again, maybe one didn't program. Be careful handling the boards as one of the IC's is static sensitive.
Posts: 25
Threads: 5
Likes Received:
0 in 0 posts
Likes Received:
0 in 0 posts
Reputation:
0
Joined: Jan 2016
Country:
Hi Rob,
The previous version worked well.
I programmed Arduinos again, but the problem remains the same. I tried synchronization between the power bar and the display which passed successfully. I can send you video.
Thanks in advance
Posts: 40
Threads: 3
Likes Received:
0 in 0 posts
Likes Received:
0 in 0 posts
Reputation:
1
Joined: Oct 2015
Country:
Hello vilich,
I had a similar issue with the Mega when I first received it and performed my initial upload of R-T. Did you remove the Mega from the power board to update the program or did you leave it plugged into the board while performing the update?
The reason I ask is that I had an issue with the Mega's communication ports (Rx, Tx) making contact with the power board. The headers for the ports 14 through 21 contain the communication between the Mega and the Power PCB. This header, I had found during my trouble shooting, was ever so slightly loose on the Mega. I received the same initially green icon which after a few seconds would turn red. I'm not sure if you are indicating alternating between red and green. Mine did not alternate.
Rob caught the issue in a photo I sent him and suggested that I run a soldering iron along the header on the Mega to reattach it. Fearing I would cause more damaged to the Mega, I simply removed and re-seated the Mega while carefully observing that all the pins went into their respective places in the header.
Make sure that all the pins from the power board go securely into the header on the Mega. Even take a flashlight and look under the mounted controller to make sure no pins have misaligned.
I had been hesitant to update my software as my PCB does not allow a software reset and requires the removal of the Mega to reprogram it. I have an early production PCB that requires the cutting of a trace to allow a software reset of the Mega while mounted on the board during a software upgrade. Without the cutting of that trace coupled with earlier versions of the code (prior 1.6), a software reset of the Mega cannot occur, so upgrades require the removal of the Mega. Rob has now addressed resetting through software and cutting the trace is not necessary. The Mega can now be upgraded while attached to PCB and the trace does not have to be cut. (Have I got that correct, Rob??)
I waited until ver 2.0 to remove, upgrade, and remount. All went well, whew!
I don't think there would be any issue with your display or connecting cord. I believe the icon on the Home screen was designed to show that communication connections between the Mega and power board are working.
Else, I'm stumped. Your thoughts, Rob??
Posts: 3,251
Threads: 90
Likes Received:
163 in 120 posts
Likes Received:
163 in 120 posts
Reputation:
184
Joined: Sep 2015
Country:
Hi Vilich, sorry I'm a little confused. If there's no communications the synchronizing shouldn't have worked. Could you send me a video so I can see what's going on.
Your correct Steve, the mega can now stay on the board and be updated without removing it. You shouldn't have to do that again.
Posts: 25
Threads: 5
Likes Received:
0 in 0 posts
Likes Received:
0 in 0 posts
Reputation:
0
Joined: Jan 2016
Country:
Hi Rob,
The problem is solved according to your instructions.
Soon I will upload pictures of Robo-Tank controller.
Thanks so much for your help.
All the best.
Posts: 3,251
Threads: 90
Likes Received:
163 in 120 posts
Likes Received:
163 in 120 posts
Reputation:
184
Joined: Sep 2015
Country:
Great, glad to hear its working again, I'll send you a new IC so you can replace it or put it in the drawer.