04-05-2023, 09:33 AM
Rob,
Thank you, I was able to get into the system after I followed the steps above. One thing that I did which was not correct was used the code as you provided - sudo usermod -a -G www-data username, this did not work, then I changed the username to reefpi, don't like pi, then it worked.
I am moving from a reef-pi system to Robo Tank software so a few things are confusing. Is there a manual that tells the setup process. It would be great if you can create separate how to documents and add a link to the document on the page where the setup is being done, this will make it easy for folks like me to get to the document, easy for you to make changes to just that document as you are adding more features. It would be great if you can add a send feedback text box as default on all the pages so we can provide you feedback directly from the page we are in.
It is very confusing on how to get the devices to turn ON after a reboot. I configured the sensors and enabled them. To me this meant that they would turn on after a reboot, but this was not the case, I then manually turned them on and clicked the red dot to resume the auto mode, this made them turn ON but after a reboot they would turn OFF - need this for return, skimmer, wave maker for my system. Also a delay would be great for skimmer to turn ON after a few minutes to allow the water levels to stabilize so that there is no overflow. I noticed that during configuration if I edited the name of a power bar port and then without saving if I added the icon, it would save the icon but cancel the change to the name. I changed all the names then added the icons and then hit the save button, this saved the changes.
Need more clarity on how the heater needs to be setup, I setup the rule to turn ON the heater if temp is >= 78. Do I need to setup a rule to turn it OFF once the temp is greater than 78.5? Is the first rule sufficient to where once the temp sensor reads 78 the system automatically turns off the heater? Also did not see an option to calibrate the temp sensor.
I tried to setup the ATO and had a major water leak in the house because the ATO did not turn OFF. Need more clarity on how to get ATO setup done.
At this time I want to get the basic features working and need help to get this done.
Thank you for your prompt response as always!
Ramana
Thank you, I was able to get into the system after I followed the steps above. One thing that I did which was not correct was used the code as you provided - sudo usermod -a -G www-data username, this did not work, then I changed the username to reefpi, don't like pi, then it worked.
I am moving from a reef-pi system to Robo Tank software so a few things are confusing. Is there a manual that tells the setup process. It would be great if you can create separate how to documents and add a link to the document on the page where the setup is being done, this will make it easy for folks like me to get to the document, easy for you to make changes to just that document as you are adding more features. It would be great if you can add a send feedback text box as default on all the pages so we can provide you feedback directly from the page we are in.
It is very confusing on how to get the devices to turn ON after a reboot. I configured the sensors and enabled them. To me this meant that they would turn on after a reboot, but this was not the case, I then manually turned them on and clicked the red dot to resume the auto mode, this made them turn ON but after a reboot they would turn OFF - need this for return, skimmer, wave maker for my system. Also a delay would be great for skimmer to turn ON after a few minutes to allow the water levels to stabilize so that there is no overflow. I noticed that during configuration if I edited the name of a power bar port and then without saving if I added the icon, it would save the icon but cancel the change to the name. I changed all the names then added the icons and then hit the save button, this saved the changes.
Need more clarity on how the heater needs to be setup, I setup the rule to turn ON the heater if temp is >= 78. Do I need to setup a rule to turn it OFF once the temp is greater than 78.5? Is the first rule sufficient to where once the temp sensor reads 78 the system automatically turns off the heater? Also did not see an option to calibrate the temp sensor.
I tried to setup the ATO and had a major water leak in the house because the ATO did not turn OFF. Need more clarity on how to get ATO setup done.
At this time I want to get the basic features working and need help to get this done.
Thank you for your prompt response as always!
Ramana
