(04-07-2019, 01:13 PM)Dom59 Wrote: Hi Rob,
I preupdated the both controller and display, waited 7 minutes, uploaded sketches. Same result, ASAP I touch screen, it goes black and blocked. Even if I restart. Quite same as Fietsenrex.
Hi Dom, oh no, here we go again lol...
Can you start by sending me output on serial monitor for both display and controller.
(04-07-2019, 01:20 PM)fietsenrex Wrote: good to know, thats why I had to input a start time and duration :P
Exactly, everything for lights is done on that mode, you create the temp modes there as well and toggle them on/off using shortcut on home page dock. Definitely go over that first post, there's lots there.
another issue, I figured lets do a power cycle so everything can get resetted.
but as soon as I powered back on is got stuck and doesn't start anymore..
I assume only one dot on splash, try pressing and holding top left corner, screen will go black which is ok, you should hear a beep after a second or two and the display will restart.
Managed to press the reset on the controller and got it running :)
Reason I Did is was because the CO2 got switched on when it Should have been off
It Should switch on tomorrow at 0700 local But that wasn’t the case as it switched on at 2100 local
Good to hear. I happened to plug in my router to my test controller again last night and as I was testing the libraries for you I happened to notice when the controller is reset with the internet enabled the display home page starts up with all kinds of crazy numbers showing for temp sensors. If you only restart the display with controller running its ok. So I'll have a fix soon for that.
Hi, version v5.11 is ready for download, the password is the same as 5.10. This only requires the display and controller sketches to be uploaded. If you have the web features enabled with local weather forecast on home page and it doesn't appear when controller is started this update will fix that. Also if you have web enabled and controller starts some of the min/max values for the parameters were wrong, this has been fixed as well.
04-08-2019, 12:26 AM (This post was last modified: 04-08-2019, 12:28 AM by fietsenrex.)
couldn't find it in the V5.0 post but is it normal that all AC outlets are shown in OFF state when the controller is in automatic mode?
some are on, some are off but it doesn't show correctly.
Also the current light mode is "stuck" on mode 7 which is the last mode from yesterday but it shows the start time of the first light mode and the start time of the last light mode.
I've attached a picture of the screen hopefully it helps.
also next to the dosing I've selected the feeding, it goes to the feeding menu but the icons and feed time aren't shown.
feeder is enabled and the port is activated.
That's not normal, they should work. Just like v4.2 if you tap the outlets on home page you get the screen to manually turn on/off. When you select one it should change to green/gray with a red M on it. When you go back to home page it should be the same.
I see you have an empty box, I assume you disabled some of the ports on the "hardware connected" screen? For the heck of it can you enable all ports and see if that fixes it.
As for the light mode its normal to be in the last mode as you haven't gotten to your first schedule time yet in the picture, hopefully that cycled ok. However you shouldn't see a 7 unless you put that as a custom name for that mode. The name should be showing.
04-08-2019, 11:11 AM (This post was last modified: 04-08-2019, 11:36 AM by Dom59.)
(04-07-2019, 01:20 PM)Rob F Wrote:
(04-07-2019, 01:13 PM)Dom59 Wrote: Hi Rob,
I preupdated the both controller and display, waited 7 minutes, uploaded sketches. Same result, ASAP I touch screen, it goes black and blocked. Even if I restart. Quite same as Fietsenrex.
Hi Dom, oh no, here we go again lol...
Can you start by sending me output on serial monitor for both display and controller.
Sounds good, I did fixed that problem with screen going black when you touched it if controller wasn't connected but that should have never happened. After you upload on display and controller open the Arduino IDE serial monitor to verify it says v5.11, This should read 50 = 50 and it found SD card.
Great, I'm sending you an email to download some files.
Delete all the libraries in your documents/libraries/ folder and copy all the libraries from download over to that directly.
Then upload the v5.11 controller sketch from main download package but in the files I just sent there's a sketch for display, use that one. This should fix touch as well.