My build - Printable Version +- Robo-Tank DIY Aquarium Controller Forum (https://www.robo-tank.ca/forum) +-- Forum: Robo-Tank Arduino Based - NO LONGER AVAILABLE (https://www.robo-tank.ca/forum/forum-16.html) +--- Forum: Robo-Tank Gallery (https://www.robo-tank.ca/forum/forum-20.html) +--- Thread: My build (/thread-175.html)

My build - fietsenrex - 10-19-2016 Just my build for some inspiration to people who still have no idea how to fit the controller nicely out of sight or just need some inspiration Frontside Backside Dosing pumps I still need to make an enclosure for the display unit Small side note, the programming cable is fitted on the mega and is "dangling" out of the cabinet. All plugable ports are accessable from the front of the cabinet, it might only be a nightmare to fit the atlas sientific circuits but that would be in January hopefully. RE: My build - Rob F - 10-19-2016 Looks good, I like how you've used a board. :) Wow, those are big outlets, I don't envy them. I'm guessing all those power supplies are for your lights? RE: My build - fietsenrex - 10-19-2016 Yup 3 in Total, the 4th is a 12v supply for the controller RE: My build - Rob F - 10-19-2016 That must be a lot of light, I have a large tank and one power supply about the same size and to much light. :) RE: My build - fietsenrex - 10-20-2016 well, the 12 vero18's needed 2 powersupply's to run them at full power (1A each) and the colored LEDs required also 1 for all of them at full power. but as you might imagine, 12 veros is a bit to bright for a 240gal tank... you can literally perform brain surgery next to the tank with the lights at full power, which is still half of their maximum rated power... the veros currently run at 10% and as long as everything remains stable until the end of next summer I might increase the light intensity. and as for the outlets.. there were no grounded recessed available that only had a single output, otherwise I would have gotten the recessed and saved some space and had a much cleared look RE: My build - Rob F - 10-20-2016 How's the dimming running only 10%, it won't be as smooth as using higher settings if you know what I mean? Be careful adjusting them, a few months ago for some reason I decided to increase mine and algae started growing like crazy and wasn't easy to stop even by turning back down. Wish I never touched it. :) RE: My build - fietsenrex - 10-21-2016 actually quite smooth, the "steps" are only noticeable going from M1-M2 and M2-M1. M1 is at 8 and M2 is at 100ish M3 is at 250ish and M4 is a bit under 400. but you can only see it if the room is completely dark and you pay close attention, so if you don't know you can see the steps you won't notice it. I do plan on retrofitting the wiring to have 2 or 3 veros on 1 LDD100, now every vero has its own LDD1000 which is overkill to say the least.. RE: My build - Rob F - 10-21-2016 Cool, 400 is quite low, not many steps to work with, maybe with the new wiring you'll get up to 2000. RE: My build - fietsenrex - 10-22-2016 That is why I think about retrofitting the drivers/wiring. But everything is finaly running smoothly so I don't dare to touch it.. RE: My build - Rob F - 10-22-2016 lol, yes if it ain't broke don't fix it. ;) RE: My build - fietsenrex - 10-23-2016 Well, I flooded a power supply yesterday. Had to rewire the lighting which resulted in a aquarium that was in full disco mode this morning.. So to fix everything I had to change te setup and now each LDD runs 3 Vero's. Only thing left is to adjust all the lights to the new setup, but the controller is currently in a light ramp RE: My build - Rob F - 10-23-2016 Oh no, I'm sure not the way you wanted to get it rewired. It'll be interesting to know what you set the levels at now. RE: My build - fietsenrex - 10-23-2016 Just double of what it was, high sun is now a bit over 800 RE: My build - Rob F - 10-24-2016 Still a long way from 4095 but you're probably getting the best of the fade if its not short like 10minutes. RE: My build - fietsenrex - 10-31-2016 finally got my display case build :D glue is still drying, tomorrow I'll remove the tape and maybe do some sanding on the edges and still have to make the back lid and add some magnets so it can stick to the fridge which is next to the tank. PH is false, still no money for a sensor.. RE: My build - Rob F - 10-31-2016 Looks good. I like the idea of having it on the fridge, if you use magnets make sure they are super strong, wouldn't want it to hit the floor when the door is shut. ;)