Posts: 3,249
Threads: 90
Likes Received:
163 in 120 posts
Likes Received:
163 in 120 posts
Reputation:
184
Joined: Sep 2015
Country:
Ah that makes sense, I did do some earlier changes that would have caused that. Now you can set the sensor to the non-contact, if you like a number instead of open/closed you can use the optical sensor setting.
Yeah while programming the pump will run, nothing I can do about that, if you unplug or set backup float open it'll stay off.
Posts: 355
Threads: 8
Likes Received:
12 in 12 posts
Likes Received:
12 in 12 posts
Reputation:
13
Joined: Dec 2015
Country:
04-22-2019, 10:22 PM
(This post was last modified: 04-22-2019, 10:34 PM by fietsenrex.)
Nope didn’t do a thing, still running 5.12
It has been running for a week now.
I wanted to wait till next weekend to update so I can let it run for a week and have a stable week for my water parameters.
Only thing that comes to mind is that I set the heater to manual on after maintenance and then pressed resume again
Posts: 3,249
Threads: 90
Likes Received:
163 in 120 posts
Likes Received:
163 in 120 posts
Reputation:
184
Joined: Sep 2015
Country:
Did it sort itself out or does it still show 500 on the meter?
Posts: 355
Threads: 8
Likes Received:
12 in 12 posts
Likes Received:
12 in 12 posts
Reputation:
13
Joined: Dec 2015
Country:
Nope didn’t sort itself out.
Just walked in the living room and the lights were still on and the meter still below 500
Posts: 3,249
Threads: 90
Likes Received:
163 in 120 posts
Likes Received:
163 in 120 posts
Reputation:
184
Joined: Sep 2015
Country:
Try going to hardware connected screen and enabled everything, let it restart and see if meter went to around 2000. If so then go back and disable those ports again and see if it's back to normal.
Posts: 355
Threads: 8
Likes Received:
12 in 12 posts
Likes Received:
12 in 12 posts
Reputation:
13
Joined: Dec 2015
Country:
I’ll try that this afternoon ;)
Posts: 355
Threads: 8
Likes Received:
12 in 12 posts
Likes Received:
12 in 12 posts
Reputation:
13
Joined: Dec 2015
Country:
Added all the Ports and set LED channels to 16, health meter is in the green now and checks are at 1980 ish.
We’ll see how it holds up untill the weekend.
Wierd thing is that it was running smooth for a week, and as day 7 ended it crapped out
Posts: 3,249
Threads: 90
Likes Received:
163 in 120 posts
Likes Received:
163 in 120 posts
Reputation:
184
Joined: Sep 2015
Country:
I'm not sure what happened but its probably still related to the other ports, I will be looking.
Posts: 355
Threads: 8
Likes Received:
12 in 12 posts
Likes Received:
12 in 12 posts
Reputation:
13
Joined: Dec 2015
Country:
Ran into a glitch this weekend when using 5.12
During a fade you can enter the temporary light menu and set up a temporary mode.
You also can select the temporary mode during a fade, the controller will finish the fade and then get stuck in the end point of the fade intill you select a light mode and then it will het stuck in that one.
Resetting the controller by unplugging the screen doesn’t work neither does the resume button.
A full powercycle got it working again, But the temporary mode has dissapeared
Posts: 3,249
Threads: 90
Likes Received:
163 in 120 posts
Likes Received:
163 in 120 posts
Reputation:
184
Joined: Sep 2015
Country:
Thanks I'll look into that.
Posts: 355
Threads: 8
Likes Received:
12 in 12 posts
Likes Received:
12 in 12 posts
Reputation:
13
Joined: Dec 2015
Country:
In 4.2 the lightmodes were locked during a fade if I recall correctly, So maybe you could do that again in the next update
Posts: 3,249
Threads: 90
Likes Received:
163 in 120 posts
Likes Received:
163 in 120 posts
Reputation:
184
Joined: Sep 2015
Country:
Yeah they were light modes were locked during a fade and I think I will add that again, maybe this time I'll put a "stop fade" button so someone can still access without waiting or restarting until I have more time.