Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
After installation from 4,2 to 5,13 problem
#1
Hi Rob,

Today I updated the controller from 4.2 to 5.13 as directed. I followed everything written. After the launch, the controller was updated normally and everything was OK. But all the inscriptions are back. Even when I pressed "Connect Equipment", the "Flow meters" menu opens. Everything is reversed. Is it possible that the CPLD 7 inches calibration file that I put in the library is the problem.
All the best


Attached Files Thumbnail(s)
               
Reply to top
#2
(06-12-2019, 03:52 AM)vilich Wrote: This is displayed at the beginning when updating the controller.
All the best


Attached Files Thumbnail(s)
   
Reply to top
#3
Hi Iliyan, the display is mirrored because of the library, I emailed you the correct one. Replace the libraries in your documents/arduino/libraries folder. For the touch it sounds like a calibration file error, I also sent one that should work, replace this before opening and uploading the display sketch.
Reply to top
#4
Hi Rob
I did not see the calibration file in the email.
Reply to top
#5
I put the file I believe is correct in the library folder already so just copying over the libraries should cover everything. I also added a 2nd calibration file, it's in the root directory of the download, its the UTouchCD.h file. I just looked and see its in the zip file.
Reply to top
#6
No change after uploading.
Reply to top
#7
Did you close all Arduino IDE's before uploading the sketch? If the IDE is open there's a good chance the changes weren't seen as some are loaded when the IDE is opened.
Reply to top
#8
Yes i closed all Arduino IDE's before uploading the sketch
Reply to top
#9
Hmm, that should have worked, I sent the same files I sent a few others who had the same issue. Did you remember to change the line in display sketch to CPLD display? Can you try deleting all the libraries in your documents/arduino/libraries folder and trying again. Any chance you created a backup folder for libraries in the libraries folder? If there's duplicate libraries even in different sub directories it can cause issues. It does seem like the updated libraries aren't being seen, I think the problem was in the SD library.
Reply to top
#10
Hi Rob

Yes, I changed the line in display sketch to CPLD display before compile the skript. I deleted all the libraries in my documents/arduino/libraries folder. I copied again libraries.
I formated the sd-card and copy all the files new on the sd-card. Upload display sketch, but nothing change.
Reply to top
#11
Hi Iliyan, I emailed a link to download the files again, this is a different set in case I messed up so try replacing them again.
Reply to top
#12
Had the same thing, But changing the library’s worked for me.

If you need to set up the controller in case your life support is compomised you can use a mirror. Touch isn’t affected by the inverted text
Reply to top
#13
Hi Rob

I loaded the new library and now everything is ok. Thank you very much for your cooperation.
But on the screen the temperature is written in four digits, something like 5500C, 4900C.
Reply to top
#14
No problem, glad you got it working. Curious, what version is your controller board? It'll say Rev E or something under the logo. Also as you just updated to v5 go to system, settings and press and hold restore defaults, this might sort it out.
Reply to top
#15
Yes, Rev-E.
Display is Rev-6.
Reply to top
#16
Ok that sounds good, did restoring sort out the temps?
Reply to top
#17
Hi Rob
I'm sorry. I've been busy for two days. I restored to v5, but no change for temperature.
Reply to top
#18
Hi Iliyan, no worries. It sounds like a setting isn't correct, can you try going to settings, hardware, equipment connected, and uncheck every box and then check it again.

If that doesn't work try going to settings, hardware, temp sensors and cycle the 5 seconds from DHT22 to DS18B20.
Reply to top
#19
Hi Rob,
I followed the above instructions, but nothing happened.
Reply to top
#20
When you first updated to v5 did you run the "pre-update" sketch in the package?

I'm thinking when you do the restore defaults its only happening on the display so you will have to try and load the pre-update sketch on both display and controller. After the upload completes leave the display alone for about 7 minutes, then upload to controller and do the same. Then upload the 5.13.
Reply to top


Possibly Related Threads...
Thread Author Replies Views Last Post
  Forum Profile Problem Gordon Lehmann 3 382 03-06-2019, 02:55 PM
Last Post: Rob F
  Display Problem simonv92 12 689 03-04-2019, 09:54 AM
Last Post: Rob F
  Problem with the controller when the electric current is stopped. vilich 6 1,167 04-23-2018, 04:57 PM
Last Post: rott
  Problem finding a directory. vilich 6 1,585 09-02-2017, 03:46 PM
Last Post: Rob F

Forum Jump:

Current time: 08-24-2019, 08:36 PM