The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU (datasheet). It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input / output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84 MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button.

The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with a AC-to-DC adapter or battery to get started. The Due is compatible with all Arduino shields that work at 3.3V and are compliant with the 1.0 Arduino pinout.

The SAM3X has 512KB (2 blocks of 256KB) of flash memory for storing code. The bootloader is preburned in factory from Atmel and is stored in a dedicated ROM memory. The available SRAM is 96KB in two contiguous bank of 64KB and 32KB. All the available memory (Flash, RAM and ROM) can be accessed directly as a flat addressing space.

It is possible to erase the Flash memory of the SAM3X with the onboard erase button. This will remove the currently loaded sketch from the MCU. To erase, press and hold the Erase button for a few seconds while the board is powered.

Features:

The Arduino Due has a 32-bit ARM core that can outperform typical 8-bit microcontroller boards. The most significant differences are:

  • A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock.
  • CPU clock at 84Mhz
  • 96KBytes of SRAM
  • 512KBytes of flash memory for code
  • A DMA controller, that can relieve the CPU from doing memory intensive tasks

Warning:

Unlike other Arduino boards, the Arduino Due board runs at 3.3V. The maximum voltage that the I / O pins can tolerate is 3.3V. Providing higher voltages, like 5V to an I / O pin could damage the board.

Arduino Specifications
Microcontroller AT91SAM3X8E
Operating Voltage 3.3V
Input Voltage (recommended) 7-12V
Input Voltage (limits) 6-16V
Digital I/O Pins 54 (of which 12 provide PWM output)
Analog Input Pins 12
Analog Outputs Pins 2 (DAC)
Total DC Output Current on all I/O lines 130 mA
DC Current for 3.3V Pin 800 mA
DC Current for 5V Pin 800 mA
Flash Memory 512 KB all available for the user applications
SRAM 96 KB (two banks: 64KB and 32KB)
Clock Speed 84 MHz
Length 101.52 mm
Width 53.3 mm
Weight 36 g

Write a review

Note: HTML is not translated!
    Bad           Good

Arduino Compatible DUE R3 32 Bit ARM With USB Cable Compatible All Arduino Shield

  • Product Code: Due
  • Availability: In Stock
  • $25.95 USD


Related Products

Arduino Compatible Mega 2560 R3 ATmega2560-16AU Control Board With USB Cable

Arduino Compatible Mega 2560 R3 ATmega2560-16AU Control Board With USB Cable

The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digi..

$18.95 USD

Arduino Compatible Nano V3 - ATmega328P Controller Board Improved Version

Arduino Compatible Nano V3 - ATmega328P Controller Board Improved Version

The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino..

$9.95 USD

Arduino Compatible SD Card Module Slot Socket Reader

Arduino Compatible SD Card Module Slot Socket Reader

This is SD card module slot socket reader for Arduino ARM MCU etc microprocessors and it reads and w..

$2.69 USD